A-111-5v

Description

Doepfer 111-5 V Mini Synth Voice Vintage editionFull monophonic analog synth in a single 24HP module!This is the classy Vintage (black) version with the sought after CEM chip, they don't make those anymore.Basically a v1 Dark Energy in Eurorack format.The module is in excellent shape, only a few minor scratches The Doepfer 111-5 synth voice has the following features: VCOmanual tune control (with an internal jumper the range can be set to ~ +/-1 half an octave or ~ +/-2.5 octaves)range switch -1 / 0 / +1 octavefrequency range about 30Hz ... 10kHzFM (frequency modulation) control with modulation source switch (LFO1 / off / ADSR)manual pulsewidth control for rectangle waveformPWM control with modulation source switch (LFO2 / off / ADSR)waveform switch (sawtooth / off / triangle) the sum of the waveform chosen by this switch and the rectangle is fed into the VCF (to turn the rectangle off the PW control has to be set fully CCW)external CV input for VCO frequency (1V/octave)external CV input for external PWM of the rectangleinternal CV input for frequency (1V/octave) connected to the A-100 bus via jumper, the jumper can be used to interrupt this internal connection if not wantedVCF24 dB low pass~ 12 octaves frequency rangemanual frequency controltracking switch half - off - full (internally connected to the external frequency CV input of the VCO, i.e. the VCF tracks to the VCO if the switch is set to "half" or "full" position)XM: exponential FM (frequency modulation) control with modulation source switch (LFO2 / off / ADSR)LM: linear FM (frequency modulation) control to modulate the VCF by the triangle of the VCO in a linear (!) mannermanual resonance control (up to self oscillation)external audio input (this signal is added to the VCO signal, the level should not exceed 1Vpp, otherwise clipping/distortion may occur, if necessary an attenuator has to be used, e.g. A-183-1)external CV input for filter frequency1V/octave tracking for usage of the VCF as a sine wave oscillator (not as precise as the VCO but much better than most of the other filters)VCAmanual amplitude controlAM (amplitude modulation) control with modulation source switch (LFO1 / off / ADSR)external CV input for VCA amplitudespecial control scale: exponential scale in the range from about -20dB to -80/90dB, linear scale from about -20dB to 0dB Remark: this special control scale results in a loudness behaviour that is a bit different from pure linear or exponential VCAsLFO1 and LFO2manual frequency controlwaveform switch (triangle / off / rectangle)range switch (low, audio, medium)LED display (dual green/red color for positive/negative share of the signal)the inverted LFO1 signal is available as an additional socket (to use the LFO1 signal for external modules)an internal jumper can be used to select between the LFO1 signal or the inverted LFO1 signalADSRmanual controls for Attack, Decay, Sustain, Releaserange switch (long, short, medium)blue LED displayADSR signal is available as an additional socket (to use the ADSR signal for external modules)Gate input connected to the A-100 bus via jumper, the jumper can be used to interrupt this internal connection if not wanted

This offer was fetched from reverb.com. You cannot contact the seller via ModularGrid. You have to visit their site.

Disclaimer: Modules listed for sale on the ModularGrid Marketplace are offered explicitly by their respective owners. ModularGrid is not affiliated to the sellers and takes no legal responsibility in any transaction.
The internet is a rough place and fraudulent behavior can occur. If you are concerned about dealing with strangers consider buying your module at an authorized dealer.