All Posts

Oh. Spock also looks like a cool little too . AND,  Xor OR NOT!

Yah FSK...Thanks.....Being new to modular, the snazzy FX isn't doing it for me. I have somewhat of a Moog/Roland mindset. I like the triggerman and slipped that in.

Also added dual mixers.  It doesn't seem dual multi-channel mixing in one 8 hp box is available, yet. Trying to keep it in stereo, which a few of my keyboards are lacking.

EDITED Sep 29th 2013, 13:23

Oh, Upright...you ask the million dollar question. My CFO has her reigns on my wallet. I may slowly start, then finish in a few years. Maybe by the time I am 50?

This looks great...how long before it's a reality? 

Now it's changed after advice from Muffwiggler friends. Made it longer, added some cost, but it's a more diverse system.....Thinking of sacking the Intellijel Dual ADSR for a MFB dual ADSR + adding the INtellijel Panning VCA instead of the mVCA. THoughts? See my AFF2, AFF3 synths.

Trying to keep the cost under $4k.....leaves $234 for power and rack rails.....almost there. Will make the rack.

My current modular rig.

This is how I hope to expand My January 2014 EuroRack () by July next year. It's a bit more interesting as it contains modules other than Doepfer; mainly Intellijel, Circuit Abbey, Pittsburgh Modular and TipTop Audio. It appears that I may have difficulty in obtaining the Pittsburgh Modular gear tho'.

The intention is to buy another A-100P9 case and re-arrange all new and existing modules into this monster configuration.

I've also recreated my super-droolsome system as two separate ModularGrid racks: A-100P9 Left () and A-100P9 Right ().

Again, any constructive criticisms or advice will be gladly taken on board.

EDITED Jul 21st 2013, 15:39

This is the all-Doepfer EuroRack starter modular I plan to purchase in January 2014 - I'm ordering my A-100 Owners Manual tomorrow, so the rack layout may change a little after I've absorbed all the information it contains.

What do you fellow wigglers think?

Any constructive criticism will be gladly accepted, whereas all adverse comments will be treated with derision, mashed into a crun and immediately forgotten.

i meant   Pulplogic/Erthenvar makes a tile carrier  that hold 6  tiles in 20hp   - but i see what you mean 

Well they all sit in 1U row so no they'll not move to a tile carrier, if modular grid allowed for 1U tiles be shown properly it'd great!

i  think the Eurorack Tile Carrier might be a better way to go - you can get 6 tiles in 20 hp 

I should add that I use the modular together with a laptop and some outboard gear like tape echos and delays

These are currently in two different cases for now since I have a lot of Pulplogic/Erthenvar tiles that sadly won't fit in the bigger case, but then again I'll probably outgrow these too :/

EDITED Jul 23rd 2013, 12:30

The ADSR takes a Gate signal from either your sequencer, controller keyboard, or MIDI converter, and then shapes it, so that it isn't just straight "on" and "off." The resulting shaped signal then goes to the CV IN on your VCA.

I stare at this thing. Can anyone explain how the signal gets in and out of the ADSR. Or does it merely act as an output to trigger the oscillators? Confusion on my behalf.

I like advice. This is similar to my others. I want to run a guitar through it, use it as a monosynth, use it as a rhythm section, and finally feed through it to control my old MOOG with CVgate and trigger. Maybe three of theses at a time, depending on what I am doing? Critiques are welcome because I am new at this. Controls would be via my Roland D20 keyboard/synth sequencer or an old Korg Poly 800 as just a keyboard/midi interface.

Thanks!

Additional videos of performances with this 12U case:

EDITED Feb 7th 2014, 19:21

Link to one of my first recordings with this new system here on vimeo:

EDITED Feb 7th 2014, 19:22

Recording of my piece called "Creature" Part II for MakeNoise Records, which was recorded with this system using only the MakeNoise modules.

EDITED Aug 28th 2013, 23:52

One of my latest tracks, made with this system plus an Elektron Machinedrum, and Roland R8 and TB-303...

=exper/sets/3-complex-analog-osc-tests

Pamela's Workout by ALM Busy Circuits is the Clock of all Clocks, if you ask me. To answer your question, however, you can dispense with a dedicated clock if you don't mind losing the use of a square-wave LFO, but you should consider using a Pulse/Clock Divider in conjunction (with an LFO).

THis unit is probably out of my price range. I have another version wothout a rhythm section/clock. Curious from those of you who know, would I need a clock beyond the clock out from the MIDI and LFO? THanks!

Neither of these oscillators are a bad choice - they feature regularly in my own dream/drool racks - but relegating a perfectly good VCO to lowly modulation duties would break my heart - personally, I would prefer to install a dedicated LFO (or several)

THanks Togodumnus! I need advice like this before spending my hard earned cash. The Pittsburgh and Intelligel oscillators should also work as LFO's. That's why I selected them....Is that a bad choice?

You may want to consider swapping one of your three VCOs for another VCF to compliment the Polivoks. I would, in addition, swap the Shuffling Clock Multiplier for something more useful such as an LFO.

To run a guitar (or most anything else) through a synth I would recommend the Doepfer A-119 External Inpuit/Envelope Follower, perhaps coupled with an Inverse/Offset Attenuator.

Regarding the construction of my own powered custom Euro-rack modular case(s), I plan to use the Z-Rails, Bus-Boards and Power Interfaces manufactured by TipTop Audio.

EDITED Jul 16th 2013, 01:19

Curious what those of you "who know" think of this rack. I'd plan to make the shell myself and purchase the internal electronics mounting rail. Likely, if I ever want a Rhythm section, I'd build another, smaller unit. This would be controlled by either my Roland D-20 (Keyboard/Sequencer) or my Korg Poly 800 used as just a keyboard. My real wish would be to run a guitar through it, use it as a monosynth and also to use the MIDI to control my old Moog.

Any advice on who makes good power electronicas and bus board?

Did you build your S & H module????

Did you build your S & H module????

one row intellijel

C'est une belle wishlist tout ça!!! ça donne envie:)

How about a Dixie and a uFold?

12hp to go - what fits the heart of this?

Never mind. I just discovered how easy it is to upload your own modules. I have named my version "Micromac -R 56hp".

Hi!

I need help fitting the last module. It seems that the width reported for the micromac is wrong and it should be 56hp instead of 57hp. Is it correct?

Regards,

Pere

This is actually 2x cases that live side by side - hence the "spacers" in the middle.

Notes:

The Doepfer Dual Attenuator is actually a DIY attenuator.

The two "Turing Machine" modules and "Pulses" expander were actually DIY'd as well.  Take a gander: http://synth.glitched.org ;

There's another ~50HP with all-DIY stuff; I'll upload some module pics in due time.

Goike 6U 104HP Curved Hardwood Boat (Walnut)    http://www.goike.com/node/5

Goike 6U 104HP Curved Hardwood Boat (Walnut)    http://www.goike.com/node/5

EDITED May 12th 2013, 06:50

It looks great. Proper arrangement of the modules (number and distribution) would make an excellent and intuitive system. Most 5U systems are "all-black" and noone seems to care.

Argh my eyes!! I can't focus on a single knob... I'd be lost in a second if I had this system in front of me!

you should go 168 hp rows -- great stuff 

Awesome look!

Sweet Patch on my set up #1- Phonogene MPC:

Loop into Phonogene, Phonogene Slice set to 16 (noon- I put tape on mine and marked the different slice points) Rene QCV with voltages stored(I guess recalled from Q page) to equal 16 increasing values from QVC. QVC out to A183-2 in. The 183 is modded to 4x gain rather then 1x attenuation so I offest -2.5v from the rene QCV to get ±2.5 then gain in up to get ±8.5 ish. Output of that goes into Slide in at full CW. Slide offset in the middle goes to Noon. Now touching plates on the Rene gets me MCP type action with 16 autoslives of whatever I've recorded into the Phonogene. 

Bonus feature: Clock the Rene and the PEG so that when you hit a pad on the rene it triggers the PEG, send the PEG envelope to the Play in on the Phonogene and you can dictate how many times your 1/16 chop plays. Mess with the curve for funky rythem action!

Hi there! This is my special portable case. It is actually built into a box that has a kinda cool set up. The box is big enough for 6u with a gap at the top which is exactly the right size for a 3U skiff to slide into horizontally (like a drawer) the Skiff is powered by the main box via a din tether I DIY-ed into the side of the box and skiff. Bottom row is the Skiff whicha also works nicely as a stand alone. I moded the A183-2 on the bottom row to let me convert the Rene's +5 into ±10 to control the Phonogene. I believe it to be THE BEST EVER! Other cool things... the little guy next to the E350 is an expader for the e350 with 3 bipolr attenuators but when any of the 3 don't have an in signal they are normaled to +10 and work gread as an expander for the Dixie to it's right!

... and this is a track I made with it

EDITED Jul 6th 2014, 14:57

This is Rack No.1 on ModularGrid. Planning this Rack brought me the idea to build this website.

EDITED Apr 24th 2013, 21:59

Just built this one myself from a pcb and panel blank.  Love it.  Works great.  Low noise floor.  Sounds great!